Customers compare F142425 to these similar products
Products Featured in this Video
What's up everybody It's AJ with etrailer.com Today we're gonna be checking out the Fulton XLT 2 speed boat winch. We've got installed on the trailer already. And this is going to replace our old one, that was kind of worn out. This is gonna give us a few more options than the other one. Let's check it out. One thing that sets this one apart from the one that survived there.… see more >
Info for these parts were:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
We don't carry the Knot Autoflex couplers, but we do have a solution that could work for you. You could assemble a solution of parts we offer that would consist of: • JIF Marine 2500 lb 2-speed hand winch, part #315-W2500D • Winch…
view full answer...I reached out to my contact at Dutton-Lainson and the Dutton-Lainson Covered Hand Winch - 2 Speed - Freewheel - 25' Strap - 2,600 lbs #DL17085 will mount the same as your current DL1802A #DL14627. With that said the #DL17085 will be…
view full answer...The weld-on mounting plate for the Fulton F2 Swing Up Jacks is part #F500277 and this plate's jack mounting holes are spaced at 4-1/2 inches horizontally and 3-7/8-inches vertically as shown in the linked photo. Feel free to submit a…
view full answer...The Fulton mount #F500276 hole to hole length center on center is 5-1/2 inches and the hole to hole width center on center is 4-1/2 inches. The overall is 6 by 5 inches. The bolts included are 7/8" with threads that are 16 course.
view full answer...I wish we had an adapter that woudl let you use the Fulton F2 Swing-Up Trailer Jack, PART #F1413100334 with the 5 x 4 mounting plate on your trailer but we do not have any available. You will need to either have the plate you have cut off and…
view full answer...You can convert a single axle trailer to a tandem axle but it's more extensive than just putting the extra axle on there. The current axle does need to be repositioned for proper tongue weight. You will also need to cut off the current…
view full answer...Generally when picking out a winch for a boat trailer the ratio is 2 to 1 meaning you would need a winch with roughly half the capacity as the weight of the boat. With good rollers and a short winching distance the ratio increases to 3 to 1, but…
view full answer...Assuming your tires are in good shape without any bulges the easiest way to determine if you have a bent spindle is to take a straight edge that is longer than the tire and lay it across the tire parallel with your trailer frame and then measure…
view full answer...In regards to the Fulton XLT Bolt-Thru Swivel Trailer Jack part #F26ZR, the distance from the center of the mounting bracket to the top of the jack tube cap is 13.4". I have attached a photo below as well to show this. I spoke to Fulton and…
view full answer...You are correct that Shelby is no longer in business. Based on my research it looks like your Shelby 5470A is a 2,800 pound hand winch. I wasn't able to locate the drum capacity on the 5470A but the Dutton-Lainson Hand Winch #DL15440 that…
view full answer...That's a really unusual place for winch to bend/fail. I'd be willing to be the issue is that the angle of the winch's pull is not ideal. What degree is the winch pulling from relative to the winch plate direction? Parallel?
view full answer...Yes, the strap on the #315-W3200D can be installed so that it comes from the bottom instead of the top. However, doing so will reverse the switch and the direction you turn the handle for operation. The self-locking mechanism will work either way.…
view full answer...